GEEKS SOLUCIONES: Como cambiar tactil a Blu L120

Bienvenidos a Geeks soluciones, hoy te traigo un nuevo articulo de Como cambiar el tactil a un Blu L120

Herramientas:

Destornillador
palanca de plastico
Pua de plastico o uña de guitarra y si no una tarjeta bancaria

Paso 1: Remover la tapa y bateria de celular

Image 3/3: Remove the cover by lifting the notch towards the bottom of the phone. Use your fingernail to lift it up.

Paso 2: Remover los tornillos de la carcaza del celular.

Image 1/3: Remove these nine screws with a small phillips screwdriver. They are all the same size.

Paso 3: Remover cuidadosamente el panel trasero de la carcaza con una pua o palanca de plastico.

Image 2/3: *WARNING* by doing this, you will void the manufacturers warranty.

Hagalo con cuidado deslizando la herramienta alrededor de todo el panel.

Image 3/3: *WARNING* by doing this, you will void the manufacturers warranty.

Paso 4: Separe el panel trasero del celular, separe la pieza completa con sus manos.

Image 3/3: Once you have gone around the entire frame, use both hands to pull it apart.

Paso 5: Retire la camara de la placa usando la palanca de plastico

Image 1/3: Use the pry tool to disconnect the camera from the device.

Image 2/3: Gently lift the camera up and use the tweezers to remove it from the phone.

Image 3/3: Reinstall the camera. Then follow the guide in reverse to put the phone back together.

Paso 6: Retire los tres tornillos que sujetan la placa a la carcaza del celular

Image 1/3: Remove these three screws using 00 Philips screwdriver. Note the smaller screw circled in orange.

Retire el cable coaxial de la placa

Image 2/3: Then gently pry up on the metal antenna connector at the end of the grey wire. Move the wire out of the way.

Image 3/3: Then gently pry up on the metal antenna connector at the end of the grey wire. Move the wire out of the way.

Paso 7: Desconecte los cable flex de la placa como se muestra en la siguientes imagenes

Image 1/2: Next you must disconnect these three cables.

Image 2/2: Use your pry tool to lift up on the brown tab to release the ribbon cable.

Paso 8: Para retirar el ultimo cable flexor que se encuentra bajo la ranura de tarjeta de sim, usa una palanca y presione suavemente hacia arriba

Image 3/3: The cable is now free to be pulled back out of its' slot.

Image 2/3: Using a spudger, peel up on the mesh tape then use your tweezers to peel the rest of it up.

Image 3/3: Using a spudger, peel up on the mesh tape then use your tweezers to peel the rest of it up.

Paso 9: Usando una pinza retire la pelicula amarilla para liberar los conectores de la pantalla

Image 1/2: Using your tweezers, peel back the yellow film to free the cable from the screen.

Image 2/2: Using your tweezers, peel back the yellow film to free the cable from the screen.

Paso 10: Aqui se uso una herramienta para calentar la pantalla y aflojar el pegamento, pero nosotros podemos usar un secador de cabello calentando la pantalla uniformemente con cuidado de quemar la pantalla, hazlo a unos 10 cm de separacion de la pantalla en temperatuva media baja hasta que sienta que la pantalla esta caliente al tacto.

Image 2/2: We used the iOpener tool, heated it up, and placed it on top of the phone for a few seconds to loosen up the glue.

Paso 11: Una vez la pantalla se alla calentado deslice una herramienta entre las uniones de la parte frontal de la pantalla para retirar el tactil

Image 1/3: Once the screen has been heated and the glue is tacky, put a plastic opening tool between the glass screen and the frame. Start lifting the glass away around the whole frame.

Image 2/3: Once the screen has been heated and the glue is tacky, put a plastic opening tool between the glass screen and the frame. Start lifting the glass away around the whole frame.

Image 3/3: Once the screen has been heated and the glue is tacky, put a plastic opening tool between the glass screen and the frame. Start lifting the glass away around the whole frame.

Paso 12: Cuando termine de separar el vidrio del marco con la herramienta de palanca , agarra tanto el marco y el vidrio con las dos manos y separar ambas piezas . PRECAUCIÓN , hay un cable de cinta que necesita ser retirado de la parte posterior del teléfono antes de la separación completa.